| |
Tam Tech Polypropylene, Polyethylene Adhesive / Glue |
(Polypropylene, Polyethylene Adhesives For “Hard To Bond” Materials)
No Flame or Heat Treatment Required |
| |
| Adhesives for Hard to Bond Materials || Fast Set Epoxy Gel Adhesives || Regular Set Epoxy Gel Adhesives |
| |
Product Description (Polypropylene, Polyethylene Adhesives):
Tam Tech Polypropylene, Polyethylene adhesive/glue is one of the top performing adhesives in the industry. It is a very high performance adhesive/glue designed to work with “hard to bond” materials like: HDPE (high density polyethylene), LDPE (low density polyethylene), polypropylene, ABS, nylon, teflon, rubber, TPV, fiberglass and it bonds to concrete, steel and aluminum. It is a modified polymer in a proprietary formulation supplied in a 10-1 ratio with cartridges.
Features & Benefits:
Technical Data:
| |
Lap Shear Strength (ASTM D1002)
lbs/square inch at 75 degrees |
| Cured Materials |
24 Hours |
48 Hours |
| HDPE TO HDPE |
163 |
860 |
| ABS to ABS |
280 |
685 |
| Polypropylene to Polypropylene |
105 |
760 |
| Nylon to Nylon |
226 |
310 |
| Polycarbonate to Polycarbonate |
286 |
632 |
| Teflon to Teflon |
205 |
212 |
| Styrene to Styrene |
184 |
337 |
| Steel to Steel |
335 |
1256 |
| Aluminum to Aluminum |
320 |
1025 |
| PVC to PVC |
203 |
1260 |
Tam Tech adhesive/glue will also bond combinations of the materials listed above in the chart.
VOC Content :0%
Instructions:
If material to be bonded is smooth, first rough up surface with 120 grit sandpaper or emery cloth. Then clean surface from dirt, grease, sanding particles, etc.
Then place adhesive cartridge in dispensing gun and remove cap from cartridge. Then attach static mixer. Apply uniform pressure and dispense adhesive/glue until color and consistency is uniform. (3” to 6” of material)
Then apply Tam Tech Adhesive to surfaces to be bonded and then attach materials within the three minute working time at 74 degrees F (23 degrees C).
Packaging:
35 ml (1.18 fl oz) and 825 ml (28 fl oz) cartridges, bulk units available
Curing Time:
|
42 Degrees
(lbs/sq in) |
74 Degrees
(lbs/sq in) |
95 Degrees
(lbs/sq in) |
1 Hour |
9 |
10 |
47 |
2 Hours |
21 |
24 |
49 |
3 Hours |
22 |
42 |
96 |
4 Hours |
26 |
44 |
127 |
5 Hours |
31 |
49 |
284 |
6 Hours |
35 |
58 |
392 |
7 Hours |
39 |
67 |
510 |
8 Hours |
42 |
74 |
533 |
9 Hours |
44 |
93 |
545 |
24 Hours |
74 |
287 |
558 |
48 Hours |
141 |
562 |
569 |
Limitations:
Store product on it's side at less than 85 degrees F. (29 degrees C) Substrate and air temperature should be above 40 degrees F (4 degrees C) during application. Always test a small portion of the Tam Tech adhesive/glue to insure it is mixed properly and will gain strength before proceeding.
Warning:
Skin contact may cause irritation, redness or rash.
Use safety glasses and wear protective gloves. Use with adequate ventilation or if ventilation is poor, refer to MSDS for further information. See MSDS for complete information.
For industrial use only. Keep out of reach of children. |
| |
 |
Tamarron Technology Inc.
Corporate Office:
1660 E. Tamarron Ct.
Springboro, OH 45066
Manufacturing Plants:
Nashville, TN - Kansas City, MO - Rockford, IL
Phone: 800-277-3207
Fax: 888-845-9491 |
|
| |
| Copyright© 2011 - All rights reserved. |
|
Tam Tech Polypropylene, Polyethylene adhesives are easy to apply.
Simple application with Tam Tech Dispensing Gun.
Polypropylene, Polyethylene adhesives work on many materials and shapes.
Many sizes available for jobs large and small.
Polypropylene, Polyethylene adhesive/glues by Tam Tech bond materials for exceptional performance.
|
|