24 hour support 1 800 277 3207
Polyethylene, HDPE, Polypropylene Adhesive, Glue
HDPE, polypropylene adhesive, gluePolyethylene, polypropylene adhesive, glueNozzle - Polyethylene polypropylene adhesiveGun - HDPE Polypropylene Adhesive, Glue
Tam Tech (Polyethylene / Polypropylene) Adhesive
Polypropylene, Polyethylene Adhesive / Glue For “Hard To Bond” Materials

Tam Tech Adhesive is one of the top performing adhesives in the industry. It is a very high performance structural adhesive designed to work with “hard to bond” materials like: HDPE (high density polyethylene), LDPE (low density polyethylene), PE, polypropylene, ABS, nylon, Teflon, rubber, TPE’s (like Santoprene), polycarbonate, fiberglass, PVC and it bonds to concrete, steel, aluminum and glass. It is a modified polymer in a proprietary formulation that requires no special surface preparation and it is supplied in a 10-1 ratio with cartridges.

When placing an order, add a Mixing Nozzle (TTA-35MN) required for mixing the adhesive and a Dispensing Gun (DG-35) to dispense the adhesive from the 35 ml cartridge.

$25.75 / 35 ml cartridge

SKU: TTA-35.

  • One of top adhesives in the industry
  • Bonds polyethylene & polypropylene
  • Bonds dissimilar materials
  • No special surface preparation necessary
  • Very good chemical resistance
  • Excellent resistance to water
  • Replaces mechanical fasteners
 

Instructions: If material to be bonded is smooth, first rough up surface with 120 grit sandpaper or emery cloth. Clean surface from dirt, grease, sanding particles, etc. Then place cartridge in dispensing gun and twist off cap. Pump the gun until both the black and white material comes out. Wipe the end of the cartridge clean. Then attach static nozzle mixer with a twisting motion. Apply uniform pressure and dispense adhesive until color and consistency is a uniform gray. (3” to 6” of material) Then apply Tam Tech Adhesive to surfaces to be bonded and attach materials within the three minute working time at 72 degrees F (22 degrees C). Storage: replace cap and store cartridges on their side in the shade or a cool location.

  • VOC Content: 0 % (no solvents)
  • Viscosity: Part A & Part B – 20,000 cps
  • Color: Part A - White, Part B - Black, Mixed - Gray
  • Working time: 3 minutes at 72 degrees F (22 degrees C)
  • Time To Handling Strength: 2-3 hours at 72 degrees F (22 degrees C)
  • Shore D Hardness: 60
Tam Tech Adhesive will also bond combinations of the materials listed below in the chart.
Lap Shear Strength (ASTM D1002) lbs/square inch at 75 degrees
Cured Materials24 Hours48 Hours
HDPE TO HDPE163860
ABS to ABS280685
Polypropylene to Polypropylene105760
Nylon to Nylon226310
Polycarbonate to Polycarbonate286632
Teflon to Teflon205212
Styrene to Styrene184337
Steel to Steel3351256
Aluminum to Aluminum3201025
PVC to PVC2031260

Limitations:Store product on it’s side at less than 78 degrees F. (26 degrees C). Substrate and air temperature should be above 40 degrees F (4 degrees C) during application. Cool weather will slow down cure time and hot weather will accelerate it. Always test a small portion of the Tam Tech Adhesive to insure it is mixed properly and will gain strength before proceeding with your application.

Storage & Shelf Life:Store cartridges on their side in the shade or a cool location. Shelf life is one year.

N/A

Clean Up:Clean up with a clean cloth before adhesive sets up.

Warning:Skin contact may cause irritation, redness or rash. Use safety glasses and wear protective gloves. Use with adequate ventilation or if ventilation is poor, refer to MSDS for further information. See MSDS for complete information. For industrial use only. Keep out of reach of children.

Curing Time:

42 Degrees (lbs/sq in)

74 Degrees (lbs/sq in)

95 Degrees (lbs/sq in)

1 Hour

9

10

47

2 Hours

21

24

49

3 Hours

22

42

96

4 Hours

26

44

127

5 Hours

31

49

284

6 Hours

35

58

392

7 Hours

39

67

510

8 Hours

42

74

533

9 Hours

44

93

545

24 Hours

74

287

558

48 Hours

141

562

569

Packaging: 35 ml (1.18 fl oz) cartridge, 490 ml (16.6 fl oz) cartridges and bulk units (5 gallon pails) available 

Weight.5 lbs
Dimensions8 x 8 x 8 in